Paper tape binding machine
Main features
Hot melt paper tape binding, can be used exclusively for bundling banknotes
Microelectronic circuit control, reliable performance
Photoelectric switch control operation, Simple and convenient to use
With manual and fully automatic working mode, easy to operate
The strapping force and the size of the belt loop are adjustable to meet different needs
The whole machine is compact and beautiful
A variety of strapping The form is single lane, double lane cross, etc., easy to operate.
Technical parameters
Bundling bandwidth
Bundling length
Maximum bundling size
Minimum bundling size
Net weight in kilograms.
Diameter of strapping tube
Outer diameter of the whole roll of strapping strap
Inner diameter of the whole roll of strapping strap
Single-pass strapping time is less than
Free adjustment of strapping force
Strapping strap Sealing and heating sealing
Volume length, width and height
Voltage and frequency
Banding machine operating instructions
Automatic banding machine
Using the power supply, in addition to the power switch, there is also a Door safety switch, when the strap machine replaces the strap, the power will be cut off when opening the door
The working mode of the strap machine is divided into two manual and automatic modes. The settings are adjusted on the controller, and the strap machine works by default. The mode is automatic working mode.
* Automatic mode In the automatic mode, the startup of the equipment is controlled by the material detection switch above the strapping machine. When the material is detected, the strapping machine performs strapping action. After the strapping is completed, wait for the material to be taken away. After the material is taken away, the strapping machine The machine continues to run back to the zero position and automatically feeds the tape to complete a strapping action.
* Manual mode In manual mode, the start of the strapping machine is controlled by the run button on the panel. Press this button, the strapping machine starts to perform the strapping action. The waiting time after strapping is controlled by the controller operation parameter waiting time. When the time is up The rear strapping machine continues to run back to the zero position and automatically feeds the straps to complete a strapping action.
There are two buttons on the casing, which are used to reset the belt from left to right. The functions of each button are as follows
* Tape feed button When the belt machine is in the zero position and is not performing packaging action, press Press this button and the tape feeding motor starts to feed the tape. When the tape is in place, it will automatically stop feeding.
* Reset button Press this button and the belt machine will return to the zero position.
* When in manual working mode, press this button and the strapping machine will perform packaging action.
★When the strap machine
is not in the zero position or the strap is not in place, the tape feeding and running actions cannot be started. When the strap machine is abnormal, press the reset button to reset the machine. After the strap is sent to the position to run the packaging action.
Instructions for strapping on the strapping machine
Before using the strapping machine, please be sure to confirm whether the type and width of the strapping machine are in compliance with the specifications of the strapping machine.
The direction of the belt must be in the same direction as shown in the figure to avoid more belt feeding failures.
★ Open the right door of the strap machine.
★ Install the packing belt on the white nylon feeding pulley, and the direction of the belt should be consistent with the picture.
★ Tear off the tape at the strap port and thread the strap.
★ According to the direction shown in the figure, pull the belt through the transfer wheel of the strap machine
.
★ The belt head must at least pass through the gap between the driving wheel and the driven wheel, and the belt must be threaded effectively.
★ Press the tape feed button, and the strap machine will finish threading.
Adjustment of the strapping machine
When adjusting the strapping machine, the power supply must be cut off and the power plug must be unplugged.
Since the blades used by the strap machine to cut the straps are consumables, during the design process, the middle knife and the front knife of the strap machine adopted a split design method to facilitate the removal or replacement of consumable parts. , to save costs.
The simple structure of the middle knife and the front knife of the strap machine
* The front knife and the middle blade are used to cut the tape and provide the tape cutting pressure with the bead set screw.
* During the adjustment process, the pressure between the front knife and the middle knife parts should be moderate. If it is too large, the front knife or the middle knife will not fall. If it is too small, it will cause the failure of normal tape cutting.
Adjustment method
* Remove the upper cover of the belt machine.
* Remove the entire tape guide frame.
* Use a special tool to adjust the wave bead tightening screw to adjust the pressure of the front knife and middle knife.
Fully automatic strapping machine paper strapping machine OPP film strapping machine banknote strapping machine